Brief description of recent changes and fixes on Omega2

Visit page http://www.norecs.com/index.php?page=Omega+FAQ for quick explanation of new features (includes pictures)

Version New features and fixes
------- ----------------------
2.2.6	Setnag Gen'Air pO2 reading added. Later also PID control loop for power source to automatically control the oxygen pump.
		Support for Setnag micropoas/NorECs MOSE oxygen sensor added as four parameter function MOSE(T in kelvin, E sensor voltage, A, B) where A and B are calibration factors for the sensor delivered with the sensor.
		Support for Bronkhorst EL-Flow for reading flow and writing setpoint through FlowDDE server.

2.2.5   Pot/Gal support: Solartron 1287 added. Potentio/galvano static/dynamic measurements. http://www.norecs.com/wiki/doku.php?id=1287

2.2.4	Enable bias for selected impedance spectrometers (Not a tested feature)
		Added information on IS/IC tab
		GPIB commands for measurement made visible for those who wish to know
		Invalid expressions with node references will evaluate in one special case: Index = 0 and amount of data in nodes = 0. This is meant to help staring measurements that rely on expressions.
		  
2.2.3   Save IS type node raw data, new z-view format available 'ZView format NEW type' as save file type.
		Traced and fixed a memory leak in a sub-component.
          
2.2.2   Node properties scrollable with mouse wheel                   

2.2.1   New features:
          Node properties page overhaul: All properties grouped to expandable categories on one tab.
          Right click node on the node list to clone a node.
          Reply to IDN? visible in the scan log
          Unactivate Sweep node will stop sweep
          
        Bugfix: 
          First axis on axis list was not selectable, it is now.

2.1.36  It was not possible to plot .AM1 for AU node type (Mass flow controller action node, set point). It is now added.

2.1.35  Node raw data saved in .ome format now includes all sample dimension information for IS and IC type nodes
        Graph data saved in .csv format now includes all dimension information for IS and IC type nodes included in the plot expression

2.1.34  Files without default location will not create popup warning during autosave. They will remain unsaved.

2.1.33  Fixed a bug that showed axes from other graphs available for a serie        

2.1.32  Manual save saves copy also to the autosave folder with suffix: _handsaved
        In addition to saving to autosave folder, the Autosave saves over the original measurement file
        Autosave folder does not get maintained or cleared by the software, it is the responsibility of the user to clear it
        Autosave occurs every 60 minutes

2.1.31  Serie Y values accessible via variable $S1.Y
        Gas species selector in tools

2.1.30  Ramp tool improvements
        Autosave files with continuous numbers

2.1.29  Shift + hover over series point pops up values dialog
        Agilent 34420 overload value now stored as NaN and not as 9*10^37 as the instrument provides it        

2.1.28  Ramp tool for furnace and flowmeter control
        Time units TS, TM, TH and TD for seconds, minutes, hours and days to be used in expressions. $N1.TM instead of function such as EMIN($N1.TI)

2.1.27  Furnace tool improvements
        .SF variable to determine if sweep is finished        
        Minor interface fixes such as missing status bar recovered

2.1.26  Tool for Mass Flow Controller

2.1.25  Fix AU node type instrument selection
        Autosearch support for 'SCHLUMBERGER TECHNOLOGIES, 1260 IMPEDANCE ANALYSER, 0, 0'
        
2.1.24  Improved stability for HP4192A

2.1.23  Fix unability to delete last point in data
        Improvements in Expression editor
        
2.1.22  Added support for power supply E3642A

2.1.21  Removed dialog box pop-up on data retrieval/conversion

Old information removed